Jump to content
Как правильно добавить self-test и прочую отладку в тему
Где взять тестовые сборки
Официальное хранилище ПО в виде файлов
  • 0

Kn1010 пропадает интернет под нагрузкой

Alexkn1010

Asked by Alexkn1010,

 Share

Question

Alexkn1010 Newbie

Alexkn1010

Posted
Posted

Добрый день !

Подскажите в чем может быть дело.

Роутер Kn1010 от провайдера приходит 300мб подключение PC по LAN

на роутере сетевые порты в режиме авто скорость не более 90 мб.с

Поменял входящий порт на 1000 мб.с  скорость при запуске спидтеста поднимается до 240 но через пару секунд интернет пропадает пока не перезагрузишь роутер.
В логах в этот момент такое 

  

I] Nov 19 10:37:25 ndhcps: sending ACK of 192.168.1.138 to 04:7c:16:ea:00:51. 
[I] Nov 19 10:37:25 ndm: Network::Interface::Switch: "GigabitEthernet0/0": switch link up at port 1 (1000FD/AN). 
[I] Nov 19 10:37:25 ndm: Network::Interface::Base: "GigabitEthernet0/0": "ethernet" changed "link" layer state "pending" to "running". 
[I] Nov 19 10:37:25 ndm: Network::Interface::Mtk::WifiMonitor: "WifiMaster0/AccessPoint0": STA(e0:2e:0b:c4:f4:d7) set key done in WPA2/WPA2PSK. 
[I] Nov 19 10:37:25 ndm: Network::Interface::Mtk::WifiMonitor: "WifiMaster0/AccessPoint0": STA(e0:2e:0b:c4:f4:d7) had deauthenticated by STA (reason: unspecified). 
[I] Nov 19 10:37:27 ndm: UPnP::Service: "System": redirect and forward rules deleted: tcp 21460. 
[I] Nov 19 10:37:27 ndm: UPnP::Service: "System": redirect rule added: tcp PPPoE0:21460 -> 192.168.1.138:32400. 
[I] Nov 19 10:37:27 ndm: UPnP::Service: "System": forward rule added: tcp PPPoE0 -> 192.168.1.138:32400. 
[I] Nov 19 10:37:54 ndm: UPnP::Service: "System": redirect and forward rules deleted: tcp 21460. 
[I] Nov 19 10:37:54 ndm: UPnP::Service: "System": redirect rule added: tcp PPPoE0:21460 -> 192.168.1.138:32400. 
[I] Nov 19 10:37:54 ndm: UPnP::Service: "System": forward rule added: tcp PPPoE0 -> 192.168.1.138:32400. 
[I] Nov 19 10:40:51 ndm: Core::System::Caption: template set to default. 
[I] Nov 19 10:40:51 ndm: Network::Interface::Ethernet: "GigabitEthernet1/0": speed set to 1000. 
[I] Nov 19 10:40:51 ndm: Network::Interface::Ethernet: "GigabitEthernet1/0": autonegotiation enabled. 
[I] Nov 19 10:40:51 ndm: Network::Interface::Ethernet: "GigabitEthernet1/0": duplex set to "full". 
[I] Nov 19 10:40:51 ndm: Network::Interface::Base: "GigabitEthernet1/0": interface is up. 
[I] Nov 19 10:40:51 ndm: Core::System::StartupConfig: saving (http/rci). 
[I] Nov 19 10:40:52 ndm: Core::System::StartupConfig: saving (http/rci). 
[I] Nov 19 10:40:52 ndm: Network::Interface::Ethernet: "GigabitEthernet1": link up (10HD/AN). 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "GigabitEthernet1/0": "ethernet" changed "link" layer state "running" to "pending". 
[I] Nov 19 10:40:52 pppd[561]: Modem hangup 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ppp" changed "link" layer state "running" to "pending". 
[I] Nov 19 10:40:52 ndm: Network::Interface::Ppp: "PPPoE0": connection service standby. 
[I] Nov 19 10:40:52 pppd[561]: Connect time 900.6 minutes. 
[I] Nov 19 10:40:52 pppd[561]: Sent 1457337157 bytes, received 1859380328 bytes. 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ppp" changed "link" layer state "pending" to "running". 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ppp" changed "link" layer state "running" to "pending". 
[I] Nov 19 10:40:52 ndm: Network::Interface::Ppp: "PPPoE0": connection service standby. 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ppp" changed "link" layer state "pending" to "running". 
[I] Nov 19 10:40:52 pppd[561]: Connection terminated. 
[I] Nov 19 10:40:52 pppd[561]: Sent PADT 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ip" changed "ipv4" layer state "running" to "disabled". 
[I] Nov 19 10:40:52 ndm: Network::Interface::Ip: "PPPoE0": IP address cleared. 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ppp" changed "link" layer state "running" to "connecting". 
[I] Nov 19 10:40:52 pppd[561]: Terminating on signal 15 
[I] Nov 19 10:40:52 pppd[561]: Exit. 
[I] Nov 19 10:40:52 ndm: Dns::Manager: name server 87.249.2.250 added, domain (default). 
[I] Nov 19 10:40:52 ndm: Dns::Manager: name server 87.249.16.250 added, domain (default). 
[I] Nov 19 10:40:52 ndm: Dns::Manager: name server 87.249.2.250 added, domain (default). 
[I] Nov 19 10:40:52 ndm: Dns::Manager: name server 87.249.16.250 added, domain (default). 
[I] Nov 19 10:40:52 ndm: Network::InternetChecker: Internet access lost (status: 0x0000). 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "GigabitEthernet1": "ethernet" changed "link" layer state "running" to "pending". 
[I] Nov 19 10:40:52 ndm: Network::Interface::Ethernet: "GigabitEthernet1": link down.

 

Link to comment
Share on other sites

1 answer to this question

Recommended Posts

  • 0
Monstr86 Content Generator

Monstr86

Posted
Posted

Попробуйте задействовать другой порт на кинетике для WAN, еще как вариант кабель может быть поврежден до коммутатора провайдера или порт на их стороне дефектный.

23 часа назад, Alexkn1010 сказал:

Добрый день !

Подскажите в чем может быть дело.

Роутер Kn1010 от провайдера приходит 300мб подключение PC по LAN

на роутере сетевые порты в режиме авто скорость не более 90 мб.с

Поменял входящий порт на 1000 мб.с  скорость при запуске спидтеста поднимается до 240 но через пару секунд интернет пропадает пока не перезагрузишь роутер.
В логах в этот момент такое 

  

I] Nov 19 10:37:25 ndhcps: sending ACK of 192.168.1.138 to 04:7c:16:ea:00:51. 
[I] Nov 19 10:37:25 ndm: Network::Interface::Switch: "GigabitEthernet0/0": switch link up at port 1 (1000FD/AN). 
[I] Nov 19 10:37:25 ndm: Network::Interface::Base: "GigabitEthernet0/0": "ethernet" changed "link" layer state "pending" to "running". 
[I] Nov 19 10:37:25 ndm: Network::Interface::Mtk::WifiMonitor: "WifiMaster0/AccessPoint0": STA(e0:2e:0b:c4:f4:d7) set key done in WPA2/WPA2PSK. 
[I] Nov 19 10:37:25 ndm: Network::Interface::Mtk::WifiMonitor: "WifiMaster0/AccessPoint0": STA(e0:2e:0b:c4:f4:d7) had deauthenticated by STA (reason: unspecified). 
[I] Nov 19 10:37:27 ndm: UPnP::Service: "System": redirect and forward rules deleted: tcp 21460. 
[I] Nov 19 10:37:27 ndm: UPnP::Service: "System": redirect rule added: tcp PPPoE0:21460 -> 192.168.1.138:32400. 
[I] Nov 19 10:37:27 ndm: UPnP::Service: "System": forward rule added: tcp PPPoE0 -> 192.168.1.138:32400. 
[I] Nov 19 10:37:54 ndm: UPnP::Service: "System": redirect and forward rules deleted: tcp 21460. 
[I] Nov 19 10:37:54 ndm: UPnP::Service: "System": redirect rule added: tcp PPPoE0:21460 -> 192.168.1.138:32400. 
[I] Nov 19 10:37:54 ndm: UPnP::Service: "System": forward rule added: tcp PPPoE0 -> 192.168.1.138:32400. 
[I] Nov 19 10:40:51 ndm: Core::System::Caption: template set to default. 
[I] Nov 19 10:40:51 ndm: Network::Interface::Ethernet: "GigabitEthernet1/0": speed set to 1000. 
[I] Nov 19 10:40:51 ndm: Network::Interface::Ethernet: "GigabitEthernet1/0": autonegotiation enabled. 
[I] Nov 19 10:40:51 ndm: Network::Interface::Ethernet: "GigabitEthernet1/0": duplex set to "full". 
[I] Nov 19 10:40:51 ndm: Network::Interface::Base: "GigabitEthernet1/0": interface is up. 
[I] Nov 19 10:40:51 ndm: Core::System::StartupConfig: saving (http/rci). 
[I] Nov 19 10:40:52 ndm: Core::System::StartupConfig: saving (http/rci). 
[I] Nov 19 10:40:52 ndm: Network::Interface::Ethernet: "GigabitEthernet1": link up (10HD/AN). 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "GigabitEthernet1/0": "ethernet" changed "link" layer state "running" to "pending". 
[I] Nov 19 10:40:52 pppd[561]: Modem hangup 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ppp" changed "link" layer state "running" to "pending". 
[I] Nov 19 10:40:52 ndm: Network::Interface::Ppp: "PPPoE0": connection service standby. 
[I] Nov 19 10:40:52 pppd[561]: Connect time 900.6 minutes. 
[I] Nov 19 10:40:52 pppd[561]: Sent 1457337157 bytes, received 1859380328 bytes. 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ppp" changed "link" layer state "pending" to "running". 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ppp" changed "link" layer state "running" to "pending". 
[I] Nov 19 10:40:52 ndm: Network::Interface::Ppp: "PPPoE0": connection service standby. 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ppp" changed "link" layer state "pending" to "running". 
[I] Nov 19 10:40:52 pppd[561]: Connection terminated. 
[I] Nov 19 10:40:52 pppd[561]: Sent PADT 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ip" changed "ipv4" layer state "running" to "disabled". 
[I] Nov 19 10:40:52 ndm: Network::Interface::Ip: "PPPoE0": IP address cleared. 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "PPPoE0": "ppp" changed "link" layer state "running" to "connecting". 
[I] Nov 19 10:40:52 pppd[561]: Terminating on signal 15 
[I] Nov 19 10:40:52 pppd[561]: Exit. 
[I] Nov 19 10:40:52 ndm: Dns::Manager: name server 87.249.2.250 added, domain (default). 
[I] Nov 19 10:40:52 ndm: Dns::Manager: name server 87.249.16.250 added, domain (default). 
[I] Nov 19 10:40:52 ndm: Dns::Manager: name server 87.249.2.250 added, domain (default). 
[I] Nov 19 10:40:52 ndm: Dns::Manager: name server 87.249.16.250 added, domain (default). 
[I] Nov 19 10:40:52 ndm: Network::InternetChecker: Internet access lost (status: 0x0000). 
[I] Nov 19 10:40:52 ndm: Network::Interface::Base: "GigabitEthernet1": "ethernet" changed "link" layer state "running" to "pending". 
[I] Nov 19 10:40:52 ndm: Network::Interface::Ethernet: "GigabitEthernet1": link down.

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Answer this question...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to question listing

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...