Jump to content

Файловая система для qBittorrent


Recommended Posts

Всем привет! Пытаюсь выжать максимум скорости на гигабитном канале, при закачке торрентов. Использую qBittorrent v4.3.1 на opkg (Entware), система стоит на отдельной флешке с двумя разделами: ext4 и swap на 2 Гб, Ultra (KN-1810), который не терминирует Интернет, является частью Wi-Fi системы, подключён, так-же, гигабитом к Viva (KN-1910). Диск для закачек - SEAGATE Backup Plus Slim STDR2000202, подключен через USB 3.0

Скрытый текст

# file -sL /dev/sd*
/dev/sda:  DOS/MBR boot sector; partition 1 : ID=0xee, start-CHS (0x0,0,2), end-CHS (0x3ff,255,63), startsector 1, 3907029166 sectors, extended partition table (last)
/dev/sda1: Linux rev 1.0 ext4 filesystem data, UUID=074a683b-3cf9-4ee6-bf46-7041b71d9635, volume name "sg2tb" (needs journal recovery) (extents) (64bit) (large files) (huge files)
/dev/sdb:  DOS/MBR boot sector; partition 1 : ID=0x83, start-CHS (0x0,32,33), end-CHS (0x3ff,254,63), startsector 2048, 26028032 sectors; partition 2 : ID=0x82, start-CHS (0x3ff,254,63), end-CHS (0x3ff,254,63), startsector 26030080, 4186112 sectors
/dev/sdb1: Linux rev 1.0 ext4 filesystem data, UUID=e5c65b77-1167-8cf0-49d7-e6a94ef1d0ef, volume name "OPKG" (needs journal recovery) (extents) (large files) (huge files)
/dev/sdb2: Linux swap file, 4k page size, little endian, version 1, size 523263 pages, 0 bad pages, LABEL=opkg_swap, UUID=00000000-0000-0000-0000-000000000000

# smartctl -a /dev/sda
smartctl 7.1 2019-12-30 r5022 [mips-linux-4.9-ndm-4] (localbuild)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Samsung SpinPoint M9T
Device Model:     ST2000LM003 HN-M201RAD
Serial Number:    S32VH0EE223405
LU WWN Device Id: 5 0004cf 20c2f7620
Firmware Version: 2BC10001
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Sun Mar 28 12:56:37 2021 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(22800) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 380) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   100   100   051    Pre-fail  Always       -       149
  2 Throughput_Performance  0x0026   252   252   000    Old_age   Always       -       0
  3 Spin_Up_Time            0x0023   087   087   025    Pre-fail  Always       -       4039
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       552
  5 Reallocated_Sector_Ct   0x0033   252   252   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   252   252   051    Old_age   Always       -       0
  8 Seek_Time_Performance   0x0024   252   252   015    Old_age   Offline      -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       58689
 10 Spin_Retry_Count        0x0032   252   252   051    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       42
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       664
191 G-Sense_Error_Rate      0x0022   252   252   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0022   252   252   000    Old_age   Always       -       0
194 Temperature_Celsius     0x0002   064   061   000    Old_age   Always       -       30 (Min/Max 20/49)
195 Hardware_ECC_Recovered  0x003a   100   100   000    Old_age   Always       -       0
196 Reallocated_Event_Count 0x0032   252   252   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   252   252   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   252   252   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0036   100   100   000    Old_age   Always       -       1
200 Multi_Zone_Error_Rate   0x002a   100   100   000    Old_age   Always       -       31
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       42
225 Load_Cycle_Count        0x0032   001   001   000    Old_age   Always       -       2233878

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     48270         -

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Completed [00% left] (0-65535)
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

Пока выжать удалось максимум 30 Мб/с при использовании NTFS, на днях решил потестить ext4, на ней, не больше 10 Мб/с.

Нашел на форуме, что рекомендуется NTFS, но сообщение от 2017 года, может, с того времени, рекомендации поменялись? Либо у кого есть советы, как оптимизировать ext (отключить журналирование например) опциями, что бы выжать больше? Или выше NTFS не прыгнуть?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...