-
Posts
1421 -
Joined
-
Last visited
-
Days Won
52
Content Type
Profiles
Forums
Gallery
Downloads
Blogs
Events
Everything posted by slomblobov
-
@kedimi7 Ok, I have enough information for a while. After a small modification of the code, the modem will go into the desired mode. I will provide you with the modified firmware for testing...
- 4 replies
-
- huawei usb modem
- huawei k4606
-
(and 1 more)
Tagged with:
-
@kedimi7 could you share a selftest file?
- 4 replies
-
- huawei usb modem
- huawei k4606
-
(and 1 more)
Tagged with:
-
Keenetic Runner 4G (KN-2212)
slomblobov replied to ac1's question in Community Support & Knowledge Exchange
You have provided very little information, maybe it would be better to contact technical support, they will help you.- 2 replies
-
- help me
- helpneeded
-
(and 1 more)
Tagged with:
-
KN-1811 Alcatel IK41 USB Modem 4G
slomblobov replied to Vadym Volodin's question in Community Support & Knowledge Exchange
@Vadym Volodin This issue is quite similar with NDM-3198, which is fixed in 4.1.C.4 or above. I recommend you to update the firmware. -
KN-1811 Alcatel IK41 USB Modem 4G
slomblobov replied to Vadym Volodin's question in Community Support & Knowledge Exchange
@Vadym Volodin Please share a self-test file. -
Runner 4G Can't delete SMS (and receive new if full)
slomblobov replied to Aazamandius's question in Web interface
@Aazamandius please provide a self-test file. -
Dear Alasedo, Thank you for your feedback. We sincerely apologize for any inconvenience caused by the new web interface. In version 4.1, we will be introducing a choice of interfaces, which we hope will help to mitigate any issues you have encountered. Rest assured that we will carefully consider all of the detailed comments you have provided. Thank you once again for your kind notes.
- 1 reply
-
- 4
-
ipv6 Disable NAT for IPv6
slomblobov replied to Muhep Atasoy's question in Community Support & Knowledge Exchange
This setting only affects IPv4, i.e. NAT44. It seems you need to allow IPv6 traffic to pass through the "ipv6 static" command (this is available through the CLI interface). (config)> ipv6 static Usage template: static (tcp | udp | tcpudp) [{interface}] {mac} {port} [through {end-port}] -
the IPv6 in IPv4 tunnel doesn't save IPv6 prefix
slomblobov replied to Anton S's question in Dev channel issues & test reports
@Anton S в этой теме обсуждался интерфейс TunnelSixInFour. Gre пока не поддерживает Ipv6. -
the IPv6 in IPv4 tunnel doesn't save IPv6 prefix
slomblobov replied to Anton S's question in Dev channel issues & test reports
Начиная с 4.0.A.12.1 (NDM-2637) добавлена возможность указывать маску подсети в команде: @eralde имеет смысл добавить данный функционал в Web для версий 4.x. -
It is possible to get this functionality by installing external packages. Entware Keenetic For example, to monitor APC UPS the following Entware packages may be used: apcupsd, apcupsd-cgi.
-
KN-1910 doesn't work with Alcatel IK41VE1
slomblobov replied to strange_v's question in Community Support & Knowledge Exchange
Right, it is not possible to modify standard profile. But you can create your own and set it as default. -
KN-1910 doesn't work with Alcatel IK41VE1
slomblobov replied to strange_v's question in Community Support & Knowledge Exchange
By the way, I tried to use 464xlat on the router side to workaround the IPv6 only issue , but it doesn't work. ping 8.8.4.4 -
KN-1910 doesn't work with Alcatel IK41VE1
slomblobov replied to strange_v's question in Community Support & Knowledge Exchange
It is also possible to follow a direct link and modify your profile settings(IP type): http://192.168.1.1/default.html#settings/profileManagement.html -
KN-1910 doesn't work with Alcatel IK41VE1
slomblobov replied to strange_v's question in Community Support & Knowledge Exchange
Now IPv6 it partially works: address is obtained, but prefix doesn't. LAN will not work with this configuration. The only way to make it work is to somehow enable IPv4 on the modem. -
KN-1910 doesn't work with Alcatel IK41VE1
slomblobov replied to strange_v's question in Community Support & Knowledge Exchange
Please try to enable IPv6 transport between modem and router by setting the following: interface CdcEthernet0 ipv6 address auto interface CdcEthernet0 ipv6 prefix auto -
KN-1910 doesn't work with Alcatel IK41VE1
slomblobov replied to strange_v's question in Community Support & Knowledge Exchange
It seems that your modem is connected to IPv6 network. But the modem is connected to the router via IPv4. Could you enable IPv4 or IPv4/IPv6 in modem settings? -
Yes, we are considering it.
- 1 reply
-
- 1
-
Allow IPv6 subnet in firewall
slomblobov replied to fl4co's question in Community Support & Knowledge Exchange
ICMPv6 ping was only disabled. It doesn't seem to be necessary. We are preparing a new version, hopefully it will be released soon. -
Allow IPv6 subnet in firewall
slomblobov replied to fl4co's question in Community Support & Knowledge Exchange
Yes, ICMPv6 ping forwarding rules were deleted. But there is some different solution... We have implemented DHCPv6 prefix delegation since NDMS 4.x. You may try to configure your device using the following configuration: In this configuration we have /63 network which consists of /64 LAN and delegation pool with one /64 network. No firewall rules need to be added but your VM must support DHCPv6. -
PPPoE: IPv6: Where is the (Stateless) DHCPv6 server?
slomblobov replied to rAcKShen's question in Dev channel issues & test reports
Thanks for the report. I can confirm that we lost this functionality by accident. Will be fixed in future versions. NDM-1975 NDM-2363.