KYTECHNGAMING

I showed your request to a friend of mine yesterday, and then I said the problem was solved. I was not wrong. You are great. Thank you.

Of course https://prnt.sc/UUoTIhgetTRn

when you exit the wizard, it stays in the version it should be. I did not understand why an experienced person is so stuck in this situation in the installation with the wizard. Or I don't quite understand what you want to say. Could it be a solution to remove the initial wizard component?

Hello there, When I want to send many files to disk in the file browser, there is no scroll bar on the page that opens. It causes the progress not to display properly. https://prnt.sc/SMlizzSfKthK the other is that the new PPPOE button in the mobile browser does not fit in Turkish. https://prnt.sc/jOW6NYz1r9Fl @eralde

Hello, This issue may not have been fixed. Keenetic_DATA - f3cff6b6-fe95-d701-0085-f6b6fe95d701 Keenetic_Data - 4b6ce681-0d37-442e-82fb-c9c89b3cf249 I wanted to change disk. I'll use the one starting with 4b instead of the one starting with f3. I inserted both disks into the Keenetic. I also removed the disks from SMB beforehand. I authorize access to disks. One is not accepted. Image of the two disks in the interface: https://prnt.sc/vqiwpKyJZyF4 Screen Record: https://disk.yandex.com.tr/i/qXclBGqGC-gM6w

Everything seems to be fine with 3.9.a.5. @Julia Rybakova

Hello, I am doing the PPPOE information test of different Keenetic models with different routers. In the Hero KN-1011 model, information is received on the interface, but the window does not close. For this reason, you cannot save the received information. https://prnt.sc/2UAliKoc0CCn My ticket number about the results of other tests: 591186 @eralde @Le ecureuil

The reason for the problem of not receiving sms in Runner 4G, 3.9.a versions has been changed to 3.8.3 version. It appears online in RMM. But this time another network has gone offline. Keenetic Hero with KeeneticOS 3.9.a.4. I noticed it in version 3.9.a.3 too. But after a while, it became online by itself. https://prnt.sc/aRlD7d4TExRd

You can see bssid on your phone with various Wi-Fi analyzer programs.

With the 3.9.a.2 update on the Runner 4g model and now the 3.9.a.3 update on my Hero model, my networks appear offline in RMM. Also, I am currently using 3.8.x version because I have sms problem in Runenr 4G. However, KeenDNS addresses were also encountering 502 Bad Gateway errors.

bssid and mac address are slightly different. Enter the following command in CMD while connected to whichever device you need bssid. (Omni DSL) netsh wlan show networks mode=Bssid https://prnt.sc/03U4i2iizioU

Hello, I cannot exit the "event log" page when viewing RMM from my mobile phone. When I do it back, it returns to another page I opened before rmm. https://prnt.sc/D8ohQOAMhUui

5Ghz interface WifiMaster1/WifiStation0 mac bssid baglanacakcihazinbssidsi 2.4 Ghz interface WifiMaster0/WifiStation0 mac bssid omnidslbssid Just enter the command for 2.4ghz on the Lite-1 device. Because your devices only have 2.4ghz AP.

Wouldn't it be nice if new components in KeeneticOS versions had a sign next to them? If the HTTP(S)/SOCK proxy that came with 3.9.A.1 looked like this, I would have noticed it more quickly. https://prnt.sc/eWB257ON88j3

Follow this article https://help.keenetic.com/hc/ru/articles/360021888880 or https://help.keenetic.com/hc/en-us/articles/360021214160

I guess it's a hardware failure. 😟 I've heard it 1-2 times before on another model. RD will support you.

I'm guessing there are works for batch operations. We asked for a reboot. Multitasking features will be the foundation of RMM.

Hi, It would be nice to see them all in the repeater as well as we can see them all in the main controller. We fully trust your developments. Actually, I can say that while writing this development, I was just looking for a note plugin(widget). When this note plugin(widget) is full, it is enough to have a notification icon somewhere in the interface that there is a note. A more challenging scenario is; There may be a note system that notifies the change of codes made with the CLI. For example, to show commands where values diifferent from the default are set.

What is your ping check settings in wired or WISP? What is your tapology? Lan to lan for accespoint or lan to wan for double nat routing.

The problem persisted in 3.8.1. But the last thing I noticed is as follows. When the device is just turned on, it generally asks for the password. After the restart, if the entire mesh system is connected and 3-5 minutes have passed, the SMB can be accessed.

Hello, I noticed something during 3.8.1 though I'm not sure about 3.8.0. I have a mesh system with 4 Keenetic. As 1 master controller, 2 repeaters and 1 access point. In the segment settings, port 1 is set to belong to segments. https://prnt.sc/TDWrR1zWHyAI On the repeaters, the 1st port appears as "down" in all of them. Devices cannot receive ip. With the "interface up" command, the port did not start to work. The iseg role has been removed. SpeedSter extender https://prnt.sc/2KTJL4SBruP4 MiBox was plugged in my 1st port. When I switch to the 2nd port, it continues to work properly. I remember it wasn't like this before. Is it a new feature? Could you give information? Ticket #588533

Hello, I use custom settings on some devices in my mesh system. For example, static node connection... But sometimes it's hard to remember on which device I applied it. For this reason, it may be impossible for this device to reconnect in a possible relocation. If I can see this in the note, it's easy to remember and I can remove this setting first and then relocate it. Is it possible to improve on this issue in the interface or even in RMM? @eralde @Le ecureuil @Julia Rybakova

Follow this topics 👍 You can add repeaters to the mesh network with both wired and wireless connections. You can manage your network with new segments. https://help.keenetic.com/hc/en-us/articles/360005236300-Network-segments#:~:text=Keenetic routers allow organizing the,' https://help.keenetic.com/hc/en-us/articles/360002155079-Setting-up-Mesh-Wi-Fi-System

No mesh. You set it up classically. Set the switch on the back of air to D . this is access point mode. you can attach it to the mesh if you connect it to the main Air. You can create different segments from the main device interface. By default, all Keenetics come with Home network on and Guest network installed but turned off.

I have previously made a request that game engines not be included in the game class. I think it should be put in the default or download category/class. Ticket #561111 https://prnt.sc/L4UrvtM_OXzT when downloading the game: https://prnt.sc/-7YIzstblZFM