Jump to content

r13

Forum Members
 View Profile  See their activity

  • Posts

    5249

  • Joined

  • Last visited

  • Days Won

    66

 Content Type 

Everything posted by r13

  1. r13
    Your configuration should be like this to update both addresses: dyndns profile _WEBADMIN type custom no send-address url https://dyndns.inwx.com/nic/update?myip=${ip}&myipv6=${ip6}
  2. r13

    QUIC DNS

    r13 replied to Ahmed Ensar's question in Feature Requests

    С учетом что в кинетике стартует куча экземляров для политик вполне может жрать много.
  3. r13
    No, Inner v6 addressing is implemented currently. endpoints can be ipv4 only for now.
  4. r13

    QUIC DNS

    r13 replied to Ahmed Ensar's question in Feature Requests

    tcp over tls работает через stubby
  5. r13
    There is a general issue with usb on devices contains usb 2.0 only on alfa 6. So wait for next build.
  6. r13
    Yes, correct, ping check is used to determine state of interfaces. Playing around with min-success/max-fails you can fine tune its sensitivity
  7. r13
    Hi, You could fine tune ping-check via cli. Please refer to cli manual for reference. Ping-check contains parameters related to how much success checks should be done before treating inteface as alive.
  8. r13
    On beta 0.6: Sep 25 19:40:30 ndm Service: "Link-layer discovery observer": unexpectedly stopped. Sep 25 19:40:33 invalid value: "".
  9. r13
    Then keendns won't help you, it can proxy http(s) requests, but won't supply you with certificate to be used outside router's web server.
  10. r13
    Explain what is your goal. May be keendns not right service you are looking for. It won't give you any certificates to be used outside webserver in router.
  11. r13
    You don't need to obtain level4 certificate, keendns level3 is wildcard certificate and it is valid for any subdomains
  12. r13
    Ipv6 configured only for Home segment by default. In case your provider gives you prefix greater then /64 you can configure Guest segment to enable ipv6 for it It is configured by cli commands open web console - my.keenetic.net/a and apply this commands: ipv6 subnet Guest ipv6 subnet Guest bind Bridge1 ipv6 subnet Guest number 1 ipv6 subnet Guest mode slaac system configuration save Above set of commands will enable ipv6 for guest segment
  13. r13
    Не, все работает, просто в логах много подобных записей.
  14. r13
    @Le ecureuil на beta2 ошибка по прежнему присутствует. Свежий селфтест следом
  15. r13
    Как написал выше в моменте борьбы с проблемой doh были грохнуты(как возможный источник проблемы), но нет, не помогло Изначальный конфиг был типа такого
  16. r13
    @Le ecureuil Сегодня в очередной раз что-то съехало в новом ДНС прокси, в логе множественные записи вида [I] Feb 15 20:38:13 ndnproxy: rogue answer from 127.0.0.1:40548 (expect from 127.0.0.1:40552), ignore. И dns стал полностью не рабочим, резолвинг не работал Поудалял doh, думал может это перезагрузит сервис, нет, не помогло. Селфтест следом
  17. r13
    Exfat/ext/ntfs format and check was introduced in 2.16 firmware 1.5 year ago, but still not ported to 3.x 😕
  18. r13
    Hi David All vpn are availiable in router mode. You have to consider to switch to it in case you want to use wireguard.
  19. r13
    Tested, works on my setup
  20. r13
    Hi its only possible via command line interface. GUI accepts only v4 addresses Command example for adding dns server: ipv6 name-server 2a10:50c0::ad1:ff
×
×
  • Create New...